View EUP7962_4116102.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

EUP7962 2A Ultra Low-Dropout Linear Regulator
DESCRIPTION
The EUP7962 is a 2A low-dropout linear regulator that provides a low voltage, high current output with a minimum of external components. It offers high precision, ultra-low dropout, and low ground current. The EUP7962 operates from an input of 2.5V to 5.5V. This regulator uses small, 2.2F ceramic input capacitors and 10F ceramic output capacitors to deliver 2A output current. High bandwidth provides excellent transient response. It is designed to drive digital circuits requiring low voltage at high currents (i.e., PLDs, DSPs, microcontrollers, etc.). Other features include thermal and current limit protection, a logic-control shutdown mode and an error flag output that goes low when the output voltage drops 10% below nominal value. It is available in fixed output voltages of 1.5V, 1.8V, 2.5V, 3.3V and as an adjustable device with a 0.8V reference voltage. The adjustable output voltage can be set from 0.8V to 4.5V.
FEATURES
2A Guaranteed Output Current 600mV Dropout Voltage at 2A Output Stable with Ceramic Capacitors 1.8% Output Voltage Accuracy 1mA Low-Ground Pin Current 0.1A Quiescent Current in Shutdown Mode Excellent Line and Load Regulation Thermal Shutdown and Current Limit Protection Error Flag Indication Available in To-263,To-220 and SOP-8 (FD) Packages RoHS Compliant and 100% Lead (Pb)-Free
APPLICATIONS
LDO Linear Regulator for Low-Voltage Digital IC PC Add-In Cards High Efficiency Linear Power Supplies Post Regulator
Typical Application Circuit
Figure1.
DS7962 Ver 1.4 Oct. 2007
1
EUP7962
Block Diagram
Figure2.
DS7962 Ver 1.4 Oct. 2007
2
EUP7962
Pin Configurations
Package Type Pin Configurations
TO220-3 TO220-5
TO263-3 TO263-5
SOP-8 (FD)
Thermal Pad
Pin Description
PIN VEN VIN GND VOUT
ERROR
TO220-5 TO263-5 1 2 3 4 5
TO220-3 TO263-3 1 2 3 -
SOP-8 (FD) 3 8 6 7
DESCRIPTION Enable Input. Logic high=enable, Logic low=shutdown Input Voltage of the LDO Ground: TAB is connected to ground Output voltage of the LDO
ERROR Flag Output. Active-low indicated an output fault condition Adjustable Regulator Feedback Input. Connect to resistor voltage divider
ADJ SD NC -
2 1,4,5
Shutdown terminal No internal connection
DS7962 Ver 1.4 Oct. 2007
3
EUP7962
Ordering Information
Order Number EUP7962-15KAIR1 EUP7962-18KAIR1 EUP7962-25KAIR1 EUP7962-33KAIR1 EUP7962-15KBIR1 EUP7962-18KBIR1 EUP7962-25KBIR1 EUP7962-33KBIR1 EUP7962KBIR1 EUP7962-15LAIR1 EUP7962-18LAIR1 EUP7962-25LAIR1 EUP7962-33LAIR1 EUP7962-15LBIR1 EUP7962-18LBIR1 EUP7962-25LBIR1 EUP7962-33LBIR1 EUP7962LBIR1 EUP7962DIR1 Package Type TO220-3 TO220-3 TO220-3 TO220-3 TO220-5 TO220-5 TO220-5 TO220-5 TO220-5 TO263-3 TO263-3 TO263-3 TO263-3 TO263-5 TO263-5 TO263-5 TO263-5 TO263-5 SOP-8 1/4 1/4 1/4 1/4 Marking xxxxx P7962C xxxxx P7962D xxxxx P7962B xxxxx P7962H xxxxx P7962C xxxxx P7962D xxxxx P7962B xxxxx P7962H xxxxx P7962A xxxxx EUP7962C xxxxx EUP7962D xxxxx EUP7962B xxxxx EUP7962H xxxxx EUP7962C xxxxx EUP7962D xxxxx EUP7962B xxxxx EUP7962H xxxxx EUP7962A xxxxx EUP7962 A Operating Temperature range -40 C to 125C -40 C to 125C -40 C to 125C -40 C to 125C -40 C to 125C -40 C to 125C -40 C to 125C -40 C to 125C -40 C to 125C -40 C to 125C -40 C to 125C -40 C to 125C -40 C to 125C -40 C to 125C -40 C to 125C -40 C to 125C -40 C to 125C -40 C to 125C -40 C to 125C
EUP7962-1/4
1/4
1/4
Lead Free Code 1: Lead Free 0: Lead Packing R: Tape & Reel Operating temperature range I: Industry Standard Package Type: KA: TO220-3 KB:TO220-5 LA: TO263-3 LB: TO263-5 D: SOP
Output Voltage 15: 1.5V, 18: 1.8V,25: 2.5V, 33: 3.3V ,Black: Adjustable
DS7962 Ver 1.4 Oct. 2007
4
EUP7962
Absolute Maximum Ratings
Supply Voltage VIN ---------------------------------------------------------------------- 5.5V Package Thermal Resistance TO-263, JA ------------------------------------------------------------------------- 45C /W TO-220, JA ------------------------------------------------------------------------- 55C /W SOP-8 (FD), JA -------------------------------------------------------------------- 42.3C/W Power Dissipation, PD@TA=25C TO-263 ------------------------------------------------------------------------------ 2.2W TO-220 ------------------------------------------------------------------------------ 1.8W SOP-8 (FD) ------------------------------------------------------------------------- 0.8W Junction Temperature ------------------------------------------------------------------- 150C Storage Temperature ------------------------------------------------------ -65C to +150C Lead Temp -----------------------------------------------------------------------------260C ESD Rating Human Body Model ---------------------------------------------------------------------- 2kV
Operating Ratings
Supply Voltage VIN ---------------------------------------------------------------- 2.5 to 5.5V Enable Input Voltage -------------------------------------------------------------- 0V to 5.5V Junction Temperature ------------------------------------------------------ -40C to +125C
Electrical Characteristics
Limits in standard typeface are for TJ =25C. Unless otherwise specified: VIN= VOUT(nom) +1V, IL=10mA, COUT=10F
Symbol
Parameter
Output Voltage Tolerance
Conditions
VOUT+1V VIN 5.5V 10mA IL 2A VOUT+1V VIN 5.5V 10mA IL 2A IL = 150mA IL = 2A IL = 0A IL = 2A VEN 0.3V VO VO(NOM) -4%
EUP7962 Min Typ Max.
-1.8 0.09 0.04 41 600 1 1.3 0.01 3 3.5 1.8 0.2 0.2 50 700 1.5 1.9 10
Unit
% %/ V %/ A mV mA A A A
G VOUT
Line Regulation Load Regulation
VIN -VOUT Dropout Voltage Ground Pin Current in Normal Operation Mode Ground Pin Current in Shutdown Mode Peak Output Current
IGND
IO(PK)
Short Circuit Protection ISC Short Circuit Current
DS7962 Ver 1.4 Oct. 2007
5
EUP7962
Electrical Characteristics
Limits in standard typeface are for TJ =25C. Unless otherwise specified: VIN= VOUT(nom) +1V, IL=10mA,COUT=10F
Symbol
VIH VIL TdOFF TdON IEN
ERROR
Parameter
Enable Threshold Turn-off delay Turn-on delay VEN Pin Input Current
Conditions
Output = High Output = Low IL = 2A IL = 2A VEN=VIN
EUP7962 Min Typ Max.
1.4 0.3 15 20 0.1 8 3 10 5 0.02 1 1 1 12 7 0.1
Unit
V s A % % V s nA mA
VT VTH
Flag Threshold Threshold Hysteresis Flag Saturation Flag Reset Delay
ERROR ERROR
VEF(Sat) Td IIK Imax
ISINK=100A
Flag Pin Leakage Flag Pin Sink VError=0.5V VIN=VOUT+1V COUT=10uF VOUT=3.3V, f=120Hz BW=10Hz -100kHz VOUT=2.5V
Current
ERROR
Current AC Parameters PSRR en TSH(t) TSH(h) Ripple Rejection Output Noise Voltage Shutdown Threshold Thermal Shutdown Hysteresis
3
56 150 150 15
dB V(rms) C C
Over Temperature Protection
DS7962 Ver 1.4 Oct. 2007
6
EUP7962
Typical Operating Characteristics
DS7962 Ver 1.4 Oct. 2007
7
EUP7962
DS7962 Ver 1.4 Oct. 2007
8
EUP7962
Application Note
External Capacitors Like any low-dropout regulator, the EUP7962 requires external capacitors for regulator stability. These capacitors must be correctly selected for good performance. Input Capacitor An input capacitance of 2.2F is required between the EUP7962 input pin and ground (the amount of the capacitance may be increased without limit). This capacitor must be located a distance of not more than 1cm from the input pin and returned to a clean analog ground. Any good quality ceramic, tantalum, or film capacitor may be used at the input. If a tantalum capacitor is used at the input, it must be guaranteed by the manufacturer to have a surge current rating sufficient for the application. There are no requirements for the ESR on the input capacitor, but tolerance and temperature coefficient must be considered when selecting the capacitor to ensure the capacitance will be 2.2F over the entire operating temperature range. Output Capacitor The EUP7962 is designed specifically to work with very small ceramic output capacitors. A ceramic capacitor (temperature characteristics X7R, X5R, Z5U, or Y5V) in 4.7 to 22F range with 5m to 200m ESR range is suitable in the EUP7962 application circuit. The output capacitor must meet the requirement for minimum amount of capacitance and also have an ESR (Equivalent Series Resistance) value which is within a stable range (5m to 200m) No-Load Stability The EUP7962 will remain stable and in regulation with no external load. This is specially important in CMOS RAM keep-alive applications. On/Off Input Operation The EUP7962 is turned off by pulling the VEN pin low, and turned on by pulling it high. If this feature is not used, the VEN pin should be tied to VIN to keep the regulator output on at all time. To assure proper operation, the signal source used to drive the VEN input must be able to swing above and below the specified turn-on/off voltage thresholds listed in the Electrical Characteristics section under VIL and VIH.
ERROR Flag Operation The EUP7962 produces a logic low signal at the ERROR Flag pin when the output drops out of regulation due to low input voltage, current limiting, or thermal limiting. This flag has a built in hysteresis. The internal ERROR flag comparator has an open drain output stage. Hence, the ERROR pin should be pulled high through a pull up resistor. The ERROR pin must be connected to ground if this function is not used. It should also be noted that when the shutdown pin is pulled low, the ERROR pin is forced to be invalid for reasons of saving power in shutdown mode.
Adjustable Operation The adjustable version of the EUP7962 has an output voltage range of 0.8V to 4.5V. The output voltage of the EUP7962 adjustable regulator is programmed using an external resistor divider as shown in Figure3. The output voltage is calculated using:
V =V
O
ref
x (1 +
R1 R
2
)
Where: Vref= 0.8V typ. (the internal reference voltage) Utilize the following equation for adjusting the output to a particular voltage:
V PI = R O - 1 2 0.8V
Choose R2=50k to optimize accuracy, power supply rejection, noise and power consumption.
DS7962 Ver 1.4 Oct. 2007
9
EUP7962
Power Dissipation EUP7962 can deliver a continuous current of 2A over the full operating temperature range. A heatsink may be required depending on the maximum power dissipation and maximum ambient temperature of the application. Under all possible conditions, the junction temperature must be within the range specified under operating conditions. The total power dissipation of the device is given by:
P = V -V I +V I D IN IN GND OUT OUT
(
)
()
Where IGND is the operating ground current of the device (specified under Electrical Characteristics). The maximum allowable temperature rise (TRmax) depends on the maximum ambient temperature (TAmax) of the application, and the maximum allowable junction temperature (TJmax):
TRmax= TJmax-TAmax
The maximum allowable value for junction to ambient Thermal Resistance, JA , can be calculated using the formula:
PCB Layout Good PC layout practices must be used or instability can be induced because of ground loops and voltages drops. The input and output capacitors must be directly connected to the input, output, and ground pins of the regulator using traces which do not have other currents flowing in them. The best way to do this is to lay out CIN and COUT near the device with short traces to the VIN, VOUT, and ground pins. The regulator ground pin should be connected to the external circuit ground so that the regulator and its capacitors have a "single point ground". It should be noted that stability problems have been seen in applications where "vias" to an internal ground plane were used at the ground points of the IC and the input and output capacitors. This was caused by varying ground potentials at these nodes resulting from current flowing through the ground plane. Using a single point ground technique for the regulator and it's capacitors fixed the problem. Since high current flows through the traces going into VIN and coming from VOUT, Kelvin connect the capacitor leads to these pins so there is no voltage drop in series with the input and output capacitors.
JA =TRmax/PD
DS7962 Ver 1.4 Oct. 2007
10
EUP7962
Packaging Information
TO263-3
SYMBOLS A C2 b b1 D E e H L2 L L1 D1 E1
MILLIMETERS MIN. 4.06 1.14 0.51 1.14 8.38 9.65 2.54 14.60 1.78 6.86 6.22 15.88 1.78 2.80 1.68 0.575 0.070 0.270 0.245 MAX. 4.83 1.65 1.00 1.40 9.65 10.67 MIN. 0.160 0.045 0.020 0.045 0.330 0.380
INCHES MAX. 0.190 0.065 0.039 0.055 0.380 0.420 0.100 0.625 0.070 0.110 0.066 -
DS7962 Ver 1.4 Oct. 2007
11
EUP7962
TO263-5
SYMBOLS A C2 b D E e H L L1 D1 E1
MILLIMETERS MIN. 4.06 1.14 0.51 8.38 9.65 1.70 14.60 1.78 6.86 6.22 15.88 2.80 1.68 MAX. 4.83 1.65 1.00 9.65 10.67
INCHES MIN. 0.160 0.045 0.020 0.330 0.380 0.067 0.575 0.070 0.270 0.245 0.625 0.110 0.066 MAX. 0.190 0.065 0.039 0.380 0.420
DS7962 Ver 1.4 Oct. 2007
12
EUP7962
TO220-3
SYMBOLS A A2 b b1 C D D1 Q E E1 P e A1 L L1
MILLIMETERS MIN. MAX. 4.06 4.83 2.03 2.92 0.64 1.02 1.14 1.52 0.30 0.56 13.72 15.75 7.62 9.40 2.62 2.87 9.65 10.67 4.88 5.33 3.71 4.00 2.54 1.14 1.40 12.70 14.73 6.35
INCHES MIN. 0.160 0.080 0.025 0.045 0.012 0.540 0.300 0.103 0.380 0.190 0.146 0.100 0.045 0.500 0.055 0.580 0.250 MAX. 0.190 0.115 0.040 0.060 0.022 0.620 0.370 0.113 0.420 0.210 0.156
DS7962 Ver 1.4 Oct. 2007
13
EUP7962
TO220-5
SYMBOLS A A2 b C D D1 Q E E1 P e A1 L
MILLIMETERS MIN. 4.06 2.03 0.64 0.30 13.72 7.62 2.62 9.65 4.88 3.71 1.70 1.14 12.70 1.40 14.73 0.045 0.500 MAX. 4.83 2.92 1.02 0.56 15.75 9.40 2.87 10.67 5.33 4.00 MIN. 0.160 0.080 0.025 0.012 6.540 0.300 0.103 0.380 0.190 0.146
INCHES MAX. 0.190 0.115 0.040 0.022 0.620 0.370 0.113 0.420 0.210 0.156 0.067 0.055 0.580
DS7962 Ver 1.4 Oct. 2007
14
EUP7962
SOP-8
SYMBOLS A A1 D E1 D1 E2 E L b e
MILLIMETERS MIN. 1.35 0.10 4.90 3.90 2.00 2.00 5.80 0.40 0.31 1.27 6.20 1.27 0.51 0.228 0.016 0.012 MAX. 1.75 0.25 MIN. 0.053 0.004
INCHES MAX. 0.069 0.010 0.193 0.153 0.081 0.081 0.244 0.050 0.020 0.050
DS7962 Ver 1.4 Oct. 2007
15

▲Up To Search▲

Price & Availability of EUP7962

	To Download EUP7962 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .